108A Cut


Single to Six Phase Power Analyzer

Download 108A Datasheet.pdf


The Infratek 108A High Precision Power Analyzer is available in 1-, 2-, 3-, 4-, 5-, or 6- phase versions. All voltage inputs 0.3V up to 1500Vpeak and all current inputs (1.5mA up to 1A; 15mA up to 5A; 1A up to 40A; and shunt inputs 60mV up to 6V are potential free and exhibit low noise, high common mode suppression, excellent DC-stability, Wide frequency range (DC-2MHz) and very low self-heating on current inputs. 

There is no need to fiddle with dc-compensation, or changing current plug-ins. All is built into the input sections of the Power Analyzer, ready for measurements. It is simple to use, your intuition will guide you to operate the Power Analyzer touch screen correctly. Almost all setting changes are accomplished with two touches on the display screen or two clicks with the wireless mouse.


Four Different measuremenst functions enhance the 108A Power Analyser capabilities 

Standard Measurement Mode 

In the Standard Measure Mode 280 quantities per phase are measured without gap and are continuously updated. Values can be displayed on four display pages, can be saved in internal memory, or can be transferred via Interface to a computer. The display shows voltage, current, and power wave forms. Harmonics and bar graphs can be viewed on 5 pages. Two electric motors can be tested simultaneously. External Speed and torque inputs are optionally available. Transformer values are implemented too

Logging Measurement Mode

This measure mode is suitable for very fast measurements or for long time averaging of data. It is possible obtaining 6 datasets of a 6-phase instrument within 20ms or 6 datasets per 10 minutes.
From every phase you obtain 8 values: frequency, rms current, rms voltage, power, power factor, apparent power, energy Wh, and apparent energy VAh

Transient Measurement Mode

You can catch current-, voltage-, and power wave forms in a start-up on transient mode up to 6 phases simultaneously or you can view all the wave forms at a critical operating point.
Sections of the wave forms can be expanded by simply touching one of the 4 “Zoom Sectors”

Power-Speed Measurement Mode

This measure mode analyzes the performance of devices such as electric cars. In 20ms intervals the following data are stored in internal memory: rms current, rms voltage, power, apparent power,energy, apparent energy, and rpm of a shaft.
At end of measurement, (maximum 11 seconds) data versus time
are displayed, can be expanded to view details, or can be stored
  • Available as 1-, 2-, 3-, 4-, 5-, 6-phase instrument 
  • precision available: 0.02% + 0.02% range 
  • 18 bit resolution. High accuracy at 10% full scale 
  • Wide angle, touch-screen TFT display (800 x 480 pixels) 
  • Simple to operate, most settings in 2 steps (2 touches) 
  • Standard-, logging-, Transient-, Power-Speed measure functions 
  • Very fast data transfer; up to 3400 values per second 
  • High DC precision for solar applications 
  • 4 current inputs: 1mA – 1A, 15mA – 5A, 1A – 50A, Shunt 
  • Voltages Ranges: 0.3V to 1000V 
  • Interfaces: Ethernet, RS-232 / USB, IEEE-488, Process
  • Interface commands for fast data transmission 
  • Operating software under Windows 
  • Reasonably priced by virtue of smart design 
  • Simple servicing, modular concept, pre-calibrated inputs 
  • Optional high precision, broadband, current sensors 
  • Optional 30A coaxial shunt (current viewing resistors)
  • 1Gbyte Memory for storing measurement data 
  • 6 analog inputs and 2 frequency inputs, 12analog outputs

© Copyright 2018 Sunstate Electrical Pty Ltd      Pixel Blaze Website Design Brisbane    Developed by Pixel Blaze Web Studio

Sunstate Electrical Pty Ltd
ABN 15 010 605 071
Electrical Contractor Licence No. 7879

quality sse l safety sse l

Sunstate Electrical ENS Pty Ltd
ABN 73 161 028 066
Electrical Contractor Licence No. 75938

quality ens l safety ens l